Mechanical Part

Wanted Dodge Ram Cummins 47re Automatic Transmission

I'm looking for a 1994-2002 dodge ram cummins 47rh or 47re transmission preferably with the transfer case but will consider one with out the

Mott, ND

Looking for DSM Engine parts

2024-04-19 11:09:20

I have a 1993 Plymouth Laser Turbo and I'm searching for pretty much everything on the timing side of the engine (eg. harmonic balancer, water pump pulley, timing covers,

Dickinson, ND

2024-04-19 10:19:50

1974-1976 440 mopar spreadbore intake manifold

3830733 2 Comes with square bore adapter plate.

Surrey, ND

$40

2024-04-19 08:30:39

Lots of YBlock stuff I want to clear out.

Everything priced like scrap I just don't want it to go to waste if someone needs a teapot intake, 2v intake, manifolds, exhaust cross over tube, small items

Bismarck, ND

Multiple Prices

2024-04-19 08:21:48

parting out 2003 gmc 2500 with a 8.1 motor runs great 2500.00 for the motor alot

of good parts on the truck yet also parting out 2014 chev 1 ton truck has a good 6.0 v8 motors can hear it run 1500.00

Bismarck, ND

$2,500

2024-04-19 07:36:30

new world products sbc cylinder head

sportsman ll brand new had the seats replaced because factory had them to deep and they also milled it .040 more than they should have it would take a .075 thick

Beulah, ND

$100 OBO

2024-04-19 07:22:01

Selling a 5.7 Vortec from a 97 C2500. Engine has about 200k. Engine is complete top to bottom minus starter and ac compressor. NO HOLDS

5.7 Vortec

Minot, ND

$800

2024-04-19 06:12:50

Manton Series 4 Pushrods 3/8”x.145” Wall 8.200” length. Have 5/16” tips on

each end. Set of 8. Brand new just ordered the wrong length.

Nortonville, ND

$150

2024-04-19 01:24:34

Grand Prix parts: I have a good hood and hood latch with front bumper cover, head

I have a good hood and hood latch with front bumper cover, headlights and headlight brace from a 2005 Pontiac Grand Prix.

Bismarck, ND

Rough Country 3.5 inch leveling kit for a 2011-2019 Chevy-GMC 2500 with upgraded

2024-04-18 23:17:27

8 Photos

Rancho front shocks. Upper control arms not included.

Bismarck, ND

$250

2024-04-18 22:12:14

WANTED : chevy transmission with transfer

WANTED: chevy transmission with transfer case must work and shift and the drive shaft must be on the right side looking for transmissions th400- 700r4- th300 th350 if u have one u are selling or junking

Bismarck, ND

2024-04-18 19:49:44

1988 jeep 4.0 engine and auto transmission from Comanche, ran when pulled, have co

mputers and wiring harness, gas tank ,starter,alternator a/c pump and drive shaft.

Moffit, ND

$350

2024-04-18 17:02:33

West River Equipment is a Fleetguard filter dealer. Call us for all the filters you need for your diesel engine! - Fuel filters - Oil filters - Hydraulic filters - Air filters Conveniently

Fleetguard Filters!

Mandan, ND

Multiple Prices

2024-04-18 16:32:36

Ford Alternator! Came off a 94 Ford Explorer with a 4.0liter. Will fit multiple

years and vehicles. May deliver to Bismarck or Minot.

McClusky, ND

2024-04-18 16:32:13

Standard Idle Air Control Valve and new gasket. This is a fully functional valve

in working condition. Valve fits 96-98 Ford Ranger, Explorer, and Aerostar. Comes with a brand new gasket for installation.

McClusky, ND

$20 OBO

2024-04-18 16:30:57

Ford exhaust manifold! Left (Driver) side exhaust manifold fits Ford 260,289,

and 302 engines from 1963-1969 cars! Great shape and no cracks! May deliver to Bismarck.

McClusky, ND

$60 OBO

2024-04-18 16:30:34

Ford Mustang clutch kit. New Rhino PAC clutch kit fits 3.8 and 3.9 V6 Mustangs.

3.8 9404 and 3.9 04 models. Throw out bearing and alignment tool is missing but everything else is there. May deliver

McClusky, ND

2024-04-18 16:29:22

Brand new Isuzu ignition starter switch. This part is a Standard Motor Product.

This fits 1981-1987 Isuzu pickups Trooper, I-Mark, etc. May deliver to Bismarck.

McClusky, ND

Off of a late 70's early 80's passenger side drop, kingpin Dana 60. Big hub style. Seem to be in good shape, got em with a project truck. Don't need them.

2024-04-18 16:14:55

Dodge Dana 60 hubs

Dickinson, ND

$60 OBO

2024-04-18 15:26:38

Ford FE blocks, cranks and rods.

FE blocks that have been bored but still likely good for more. Bores range from 20-30 over. $50 a block. 391 cranks $100 390 cranks cores $100. 390/427/428/391

Bismarck, ND

Multiple Prices

2024-04-18 15:07:58

Ford 2.3 has comp cam in it, ported efi intake that was welded for carb use, head

was milled for higher compression. ran good with great oil pressure, but smoked. So it will need to be freshened up.

Underwood, ND

$300 OBO

2024-04-18 11:59:32

B AND M QUICKSILVER SHIFTER. CAME OUT A 79 PONTIAC FIREBIRD. NOTHING WRONG WITH IT

, JUST CHANGED BACK TO STOCK GM SHIFTER. COMES WITH A CUSTOM MADE WALNUT HANDLE BALL. SELLING AS IS COND. NEW THESE

Minot, ND

$125

2024-04-18 10:47:59

700r4 transmission from a Chevy

. 2 wheel drive Works good

Dickinson, ND

$400

2024-04-18 09:26:12